Skil 3320-01 10 in. Drill Press with Laser

(3 customer reviews)
Add to wishlistAdded to wishlistRemoved from wishlist 0
Add to compare

 

  • 1/2-Inch keyed chuck. Bump-off switch for added safety
  • 5 Speeds – 570 – 3,050 RPM
  • Adjustable depth stop for accurate measurements and repetitive drilling
  • 0-45 Degree Left/Right Tilting Work Surface
  • Laser X2 2-beam laser for precise hole alignment

 

SKU: 3320-01 Category:

$132.99


This Drill Press features the Laser X2 two beam laser to ensure precise alignment in your drilling jobs time after time.

Drilling depth is easily controlled with the convenient knob that sets the height of the large, tilting work surface.

The model 3320-01 has five speeds to complete drilling applications in a wide variety of materials with ease.

For repetitive drilling tasks, the adjustable depth stop ensures consistency in the depth of each hole.

Specification: Skil 3320-01 10 in. Drill Press with Laser

Part Number

Item Weight (pounds)

50.8

Product Dimensions

21.8 x 15.2 x 9.8 inches

Item model number

3320-01

Voltage (volts)

Brand

Skilsaw

UPC

039725033468

3 reviews for Skil 3320-01 10 in. Drill Press with Laser

3.0 out of 5
1
0
1
0
1
Write a review
Show all Most Helpful Highest Rating Lowest Rating
  1. K F

    I used to own a previous version of this drill press, 3320-01, for the last 5 years, which wasn’t great but usable and decided to add the “new” one, 3320-02. In the intervening time, SKIL got acquired by Bosch, and I figured, at least some aspects of the previous model would be improved along the way. What a wishful thinking.Among three or so distinct 10″ drill press designs (all made in China), SKIL stands somewhat alone in that it has a different belt tension system (the motor slides in and out instead of side-swinging) and it uses a 60mm column as opposed to 58mm (2.25″) found in Craftsman and WEN models.But that’s where the “positives” end. The rest is an exercise in cost cutting and reducing quality control (if that’s possible):1) The column base collar is made out of cast aluminum, instead of cast iron, as on ANY other drill press. Someone figured that a 50lb head, under constant vibration and stress would be fine sitting in aluminum collar, which isn’t even a solid casting, but ribbed. When tightening the screws you can literally see how it begins to distort under pressure.2) My press came with a buzzy, rattly motor and no effort to tighten it up or adjust the belt tension made any difference – it buzzed and vibrated the entire head.3) The unit comes now equipped with aluminum quill (!) The quill tube (or the spindle sleeve, as it’s called sometimes), the part that slides up and down driven by the feed handles through the gear shaft is probably the single most important part of any drill press. What a great way to save a few pennies. Wonderfully, this isn’t even a solid aluminum either, but has ribs on the inside, as you’d often see in cast parts.On my unit, the quill came dry as a bone (not a whiff of a lubricant) and had about 1/16″ (1.5mm) of lateral play. Somehow, even WEN (which I looked at too) – which isn’t exactly synonymous with quality brand – figured how to remove any play in quill tubes, but the German-owned SKIL apparently cannot.No fear, I’ve got grease and there is that set screw on the side that’s there to tighten up the quill, right? Wrong! The quill adjustment set screw, instead of ending with an extended point (“dog point”), is simply flattened on the sides. The flats are apparently intended to match the quill channel, but the side-effect is that any adjustment would have to be made in half-turn increments! (And of course, since it’s on the inside, you cannot really see whether you aligned the flats with the channel or not).We still have customer service, surely SKIL still has US-based, trained technicians? Not! After about half an hour on the phone with a very nice girl, to whom I explained the intricate differences between the drill press quill, the bed spread quilts, and the porcupine needles, we figured what replacement part I needed. She volunteered to locate the part – and then called me an hour later notifying they are no longer available, discontinued, obsolete, no more manufactured. You can actually check this yourself on boschtoolsservice.com. No third party sites carry replacement parts either.Waxing a little philosophically here, I can’t but wonder who decided that a 10″ drill press *must* cost $120? Maybe, in the grand American tradition, you’d get a better quality, when you go with a bigger model (and everyone knows that a bigger car is always better, as is the fridge or a washing machine)? But I have no use for a 12″ or 15″ drill press or desire to haul a 100-150lb unit into my workshop. On the other hand, I’d gladly pay $200-300 for a quality 10″ unit made with correct parts and with stringent quality control.This SKILL drill press is basically a piece of junk, essentially disowned by the manufacturer, and the only thing it’ll do is to further alienate any discerning customer from the brand.

    Helpful(0) Unhelpful(0)You have already voted this
  2. William E.

    I don’t usually do reviews that are positive. I mean, just how many people need to say a product is good before it’s believable? But I made an exception here because I’m rather impressed with the drill press and equally impressed with Amazon customer service.First, Amazon customer service. The drill press arrived to me with the column base broken. Actually, there’s a problem with the way it’s packaged, (see picture) not Amazon’s fault and I don’t really blame the shipper. However, since I’m on an island in the Caribbean it was quite difficult and expensive to return. Amazon offered a discount to keep the drill press if I could get it repaired here, which I did. Bravo to Amazon.Now, the drill press. As a retired quality control manager for a very large tool company, I know tools. My initial impression “out of the box” was quite positive, table is nicely machined, painting is well done and general fit and finish is excellent . Assembly was straight forward and very easy. (Note here: I’ve spoken with many customers over the years who didn’t clean the spindle and drill chuck before installing, some even applied oil, then couldn’t keep the chuck on the spindle taper. It’s very important the the spindle taper and the chuck taper be cleaned with a solvent. Any oil on either taper will result in the chuck not staying on.)I chucked a piece of drill rod and set the table to “0” using a high quality machinist square. The zero indicator was off very slightly, not enough to affect most jobs. Then checked to see how well the drill rod was parallel to the drill column and was very surprised to discovery it was almost perfect. I have to say I’m impressed.I checked the runout by placing a drill rod in the chuck, then took a measurement 100mm from the chuck. Indicated runout was 0.009″ which is a little more than I’d like to see but not bad considering the cost of this unit. I then measured how much “slop” there was between the quill and the head casting. At zero extension it measured 0.006″ and at full extension measured 0.012″. That’s actually pretty good and better than I’ve seen on some much more expensive drill presses.There is no mechanism, such as a lever, to apply tension to the drive belt but that’s not a problem, just loosen the two wing nuts and push on the motor to tension then tighten the wing nuts. The drive belt is typical low quality Chinese and is “shedding” inside the belt cover more than I would consider normal however, I don’t see this ever becoming a real problem.I do have some concern with the motor though as it gets quite hot after running for 15 minutes or so under very light load drilling 1/8″ holes in pine.I don’t find the laser sight to be particularly useful though. The “X” where the two lights beams cross is rather wide plus in bright light it’s very hard to see.In the end I am quite pleased with this small drill press. It’s accurate, well built and sturdy. It’s hands down the nicest small drill press I’ve seen and I believe would please most all users.

    Helpful(0) Unhelpful(0)You have already voted this
  3. Frank

    I’ve had this drill press for about 2 1/2 years now, and for the money, you can’t beat it for your first drill press. If you have limited space, it is especially handy, because you can carry it over to your work bench, clamp it down, at start drilling. Then stow it somewhere in a corner. However, after these 2+ years I am hitting up against some limitations that I will itemize below:1. Worst problem of all is the unreliable depth-stop feature. It is confusing and clumsy to set, and it sometimes GIVES WAY! The first time that happens and you drill through the show face of your work piece you will not be a happy camper!2. The up/down range of the table can be limiting. Not evident at first, but when you start using longer bits and trying to drill deep holes in a tall object, you suddenly find yourself swinging the table out of the way and building a lower, makeshift table.3. Runout (i.e. wobble) – if/when you try to do precision work, this unit starts to fall short; you need a table that is dead square to the bit (in 2 dimensions, mind you), and adjusting the table angle is clunky. I am not sure if the chuck/bit is exactly parallel to the post.Tip: Get yourself a good vise to sit on the table (or on a wood table that you build). The torque from the bit is very strong, and tends to cause the workpiece to move to the left (esp. with Forstner type bits)

    Helpful(0) Unhelpful(0)You have already voted this

    Add a review

    Your email address will not be published. Required fields are marked *

    Customer Service

    Customer Service
    Phone: +1 (931) 805-9138
    Email: [email protected]
     

    2020 Nezmart.com. All rights reserved.

    Sign Up for Weekly Newsletter

    Stay updated on special offers, design trends, and more.

    Visa Mastercard American Express Paypal
    Nezmart
    Login/Register access is temporary disabled
    Compare items
    • Total (0)
    Compare
    0